Your cart
There are no more items in your cart
HIGHSIDER AKRON-RS license plate holder
The HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike with its design.
The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting.
To prevent damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet.
The license plate is made of sheet steel and 2 mm thick. The precise cutting is done by laser. After edging, the weather-resistant black powder coating is applied.
This ensures the optimal fit and durability.
Through the stepless adjustment you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw.
The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal. This adjustment option allows you to adapt the position for your turn signals to the most varied number plates. To allow mounting the turn signals without disconnecting them from the wiring harness, the 10 mm holes are slotted to the side.
You can also adjust the position of the reflector individually via a slider. An adaptation to the different designs of the EU license plates is therefore no problem.
To screw the license plate securely and reduce vibration, two rubber washers are included. Another rubber buffer supports the license plate on its underside.
Details:
- model-specific bracket
- infinitely adjustable turn signal holder
- slotted turn signal holder for easy mounting without cable separation
- infinitely adjustable reflector, E-approved
- suitable for European license plates
- infinitely adjustable tilt angle
- additional screw for optimum position security
- easy fixation without further work steps (eg. Drilling)
- easy mounting of the license plate through slotted holes
Included in the scope of delivery of the HIGHSIDER AKRON-RS are:
- Model-specific bracket with mounting parts
- HIGHSIDER AKRON-RS license plate retaining plate
- Adjustable turn signal holders
- E-tested reflector with adjustable holder
- Mounting instructions
Notes:
- A special turn signal holder is optionally available for the original turn signals in the accessories tab.
- If your original number plate holder has reflectors fitted to the side, these must be refitted in a suitable position or replaced with new ones.
Tips:
If you have not found a model-specific license plate holder for your vehicle, the universal license plate holders from HIGHSIDER, which are available in many different designs, are certainly a good alternative.
The HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike with its design.
The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting.
To prevent damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet.
The license plate is made of sheet steel and 2 mm thick. The precise cutting is done by laser. After edging, the weather-resistant black powder coating is applied.
This ensures the optimal fit and durability.
Through the stepless adjustment you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw.
The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal. This adjustment option allows you to adapt the position for your turn signals to the most varied number plates. To allow mounting the turn signals without disconnecting them from the wiring harness, the 10 mm holes are slotted to the side.
You can also adjust the position of the reflector individually via a slider. An adaptation to the different designs of the EU license plates is therefore no problem.
To screw the license plate securely and reduce vibration, two rubber washers are included. Another rubber buffer supports the license plate on its underside.
Details:
- model-specific bracket
- infinitely adjustable turn signal holder
- slotted turn signal holder for easy mounting without cable separation
- infinitely adjustable reflector, E-approved
- suitable for European license plates
- infinitely adjustable tilt angle
- additional screw for optimum position security
- easy fixation without further work steps (eg. Drilling)
- easy mounting of the license plate through slotted holes
Included in the scope of delivery of the HIGHSIDER AKRON-RS are:
- Model-specific bracket with mounting parts
- HIGHSIDER AKRON-RS license plate retaining plate
- Adjustable turn signal holders
- E-tested reflector with adjustable holder
- Mounting instructions
Notes:
- A special turn signal holder is optionally available for the original turn signals in the accessories tab.
- If your original number plate holder has reflectors fitted to the side, these must be refitted in a suitable position or replaced with new ones.
Tips:
If you have not found a model-specific license plate holder for your vehicle, the universal license plate holders from HIGHSIDER, which are available in many different designs, are certainly a good alternative.
