Your cart
There are no more items in your cart
HIGHSIDER AKRON-RS license plate holder
The HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design.
The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting.
To prevent damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet.
The license plate is made of sheet steel and 2 mm thick. The precise cutting is done by laser. After edging, the weather-resistant black powder coating is applied.
This ensures the optimal fit and durability.
Through the stepless adjustment you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw.
The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal. This adjustment option allows you to adapt the position for your turn signals to the most varied number plates. To allow mounting the turn signals without disconnecting them from the wiring harness, the 10 mm holes are slotted to the side.
You can also adjust the position of the reflector individually via a slider. An adaptation to the different designs of the EU license plates is therefore no problem.
To screw the license plate securely and reduce vibration, two rubber washers are included. Another rubber buffer supports the license plate on its underside.
Details:
- model-specific bracket
- continuously adjustable turn signal holder
- slotted turn signal holder for easy mounting without cable separation
- continuously adjustable reflector, E-approved
- suitable for European number plates
- continuously adjustable angle of inclination
- additional screw for optimum position security
- easy fixing without further work steps (e. g.B. Drilling)
- easy mounting of the license plate through slotted holes
Included in the scope of delivery of the HIGHSIDER AKRON-RS are:
- Model-related bracket with mounting parts
- HIGHSIDER AKRON-RS license plate mounting plate
- Adjustable turn signal brackets
- E-tested reflector with adjustable bracket
- Mounting instructions
Tip:
Should you not have found a model-specific license plate holder for your vehicle, the universal license plate holders from HIGHSIDER, which are available in many different designs, are certainly a good alternative.
Note:
Should at your original license plate holder lateral
The HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design.
The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting.
To prevent damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet.
The license plate is made of sheet steel and 2 mm thick. The precise cutting is done by laser. After edging, the weather-resistant black powder coating is applied.
This ensures the optimal fit and durability.
Through the stepless adjustment you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw.
The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal. This adjustment option allows you to adapt the position for your turn signals to the most varied number plates. To allow mounting the turn signals without disconnecting them from the wiring harness, the 10 mm holes are slotted to the side.
You can also adjust the position of the reflector individually via a slider. An adaptation to the different designs of the EU license plates is therefore no problem.
To screw the license plate securely and reduce vibration, two rubber washers are included. Another rubber buffer supports the license plate on its underside.
Details:
- model-specific bracket
- continuously adjustable turn signal holder
- slotted turn signal holder for easy mounting without cable separation
- continuously adjustable reflector, E-approved
- suitable for European number plates
- continuously adjustable angle of inclination
- additional screw for optimum position security
- easy fixing without further work steps (e. g.B. Drilling)
- easy mounting of the license plate through slotted holes
Included in the scope of delivery of the HIGHSIDER AKRON-RS are:
- Model-related bracket with mounting parts
- HIGHSIDER AKRON-RS license plate mounting plate
- Adjustable turn signal brackets
- E-tested reflector with adjustable bracket
- Mounting instructions
Tip:
Should you not have found a model-specific license plate holder for your vehicle, the universal license plate holders from HIGHSIDER, which are available in many different designs, are certainly a good alternative.
Note:
Should at your original license plate holder lateral
